PDA

View Full Version : Cannot connect to server



lodgitek
12-30-2003, 12:47 AM
When I load up myseqserverc and myseq, it says "Waiting for new connection," and then I load up myseq and hit go, but then i get the "Cannot connect to server" error and I have no clue what to do, please help.

MQSEQ2
12-30-2003, 05:47 AM
Have you tried the Step By Step Troubleshooting guide?

NovaUSC
12-30-2003, 01:06 PM
You can add up to 5 servers on to the client and switch back and forth between them. The first time the program is used it does not recognize that the server's IP Address has been inputed. The very first time you run the program you must choose your server by selecting it's IP address under OPTIONS then SERVER SELECTION. Once you have done this it should work correctly.

Mixy!
12-30-2003, 01:11 PM
http://seq.sourceforge.net/forums/showthread.php?s=&threadid=4440

People here are willing to help you however, their patience runs thin when there's a sticky at the top of the page. :P

-Mixy!

lodgitek
12-30-2003, 02:11 PM
where are these options nova, in what program.

NovaUSC
12-30-2003, 02:19 PM
Guess I should have been more specific, my mistake. Open the MySEQ Client. The first thing you had to do was tell it what IP Address the PC running the MySEQ server had. Before you press Go, you need to click on OPTIONS and then SERVER SELECTION. You will see the IP you put in earlier. Click on it and then it should be good to go unless you change IP Addresses.

Mixy!
12-30-2003, 02:19 PM
In the client. The thing with the window and the "GO" button.

Myseq.exe

-Mixy!

lodgitek
12-30-2003, 02:24 PM
did all that yet still getting "cannot connect to server" when i hit go.

MQSEQ2
12-30-2003, 03:10 PM
Follow these steps:

http://seq.sourceforge.net/forums/s...=&threadid=4440

If the above works then do this:

In the Client hit F1 to bring up the options and set the IP address of the server in the IP Address 1 slot (remove the 127.0.0.1)

If you still can't get the turn on logging (Set it to 1) and try and then post the error logs here.

NovaUSC
12-30-2003, 03:37 PM
I'm getting a dead link of the url you posted.

I just posted a Howto for installing and setting it up in the Help Forums if this will help.

MQSEQ2
12-30-2003, 03:43 PM
I copied it from above but it's the READ FIRST post in the the Help Forum.

lodgitek
12-30-2003, 03:46 PM
F1 is doing nothing for me in the myseq client, do you have aim?

MQSEQ2
12-30-2003, 03:51 PM
I use Yahoo IM and ICQ. MQSEQ is my handle for both.

If F1 isn't working for you then you have a very old client.

NovaUSC
12-30-2003, 04:02 PM
This wouldn't be related to .NET or the required support files would it?

lodgitek
12-30-2003, 04:37 PM
no i have .NET and stuff, and i'm using the same client as my friend and it works fine for her, she has no idea why this isn't working either.

NovaUSC
12-30-2003, 05:56 PM
What version of the client and server are you using?

MQSEQ2
12-30-2003, 05:58 PM
What Server version/Client version are you using?

Have you turned on the logging?

Have you tried the Step by Step how to yet?

If we don't get any information other than it's not working then we are not going to be able to help you.