Keyring version 2.2

[NovaUSC]

I'll prolly get flamed for this but I'm willing to risk it. I'll go ahead and admit that I'm stupider than ya'll.(as is apparent by the misuse of the english language).

I'm at a loss as to my problem, it is simialr to what has already been posted but I've verified my md5sums for libEQ.a and they are correct. What i'm getting is gps only, no mob decryption. here is what my showeq box says as I run eq and load into the world and then zone.

Using config file '/usr/local/share/showeq/showeq.xml'
Loaded preferences file: /usr/local/share/showeq/seqdef.xml!
Loaded preferences file: /usr/local/share/showeq/showeq.xml!
Listening for first client seen.
Initializing Packet Capture Thread:
Filtering packets on device eth0, searching for EQ client...
Loading filters from '/usr/local/share/showeq/filters.conf'
No Zone Specific filter file '/usr/local/share/showeq/filters_unknown.conf'.
Loading default '/usr/local/share/showeq/filters.conf'.
GuildMgr: WARNING - could not load guildsfile, /usr/local/share/showeq/guilds2.d
at
Categories Reloaded
Error opening map file '/usr/local/share/showeq/unknown.map'!
Opcode Logging Mask: 0 0 0
set_decoder_key: User specified key port: 13325
==> EQInterface::savePrefs()
Finished saving preferences to file: /usr/local/share/showeq/showeq.xml
saveMap()
Error saving map ''!
Listening for next client seen. (you must zone for this to work!)
Filtering packets on device eth0, searching for EQ client...
set_decoder_key: User specified key port: 13325
Decrypting and dispatching with key: 0x0000000000000000
Client Detected: 192.168.1.105
EQPacket: SEQStart detected, pcap filter: EQ Client 192.168.1.105, Client port 1
691, Key port 13325
EQPacket::dispatchZoneData():CharProfileCode:Not Decoded
Loaded map: '/usr/local/share/showeq/Nektulos.map'
No Zone Specific filter file '/usr/local/share/showeq/filters_nektulos.conf'.
Loading default '/usr/local/share/showeq/filters.conf'.
TIME: 13:39 04/16/3173
EQ EPOCH OCCURRED AT 794313360 SECONDS POST UNIX EPOCH
CPlayerItems: count=45 size=21066 packetsize=468 expsize=468
Can't find spawn point file /usr/local/share/showeq/nektulos.sp
No Zone Specific filter file '/usr/local/share/showeq/filters_nektulos.conf'.
Loading default '/usr/local/share/showeq/filters.conf'.
Your player's id is 502
Loaded map: '/usr/local/share/showeq/Lavastorm.map'
Can't find spawn point file /usr/local/share/showeq/lavastorm.sp
Loading, Please Wait... (Zone: 'lavastorm')
No Zone Specific filter file '/usr/local/share/showeq/filters_lavastorm.conf'.
Loading default '/usr/local/share/showeq/filters.conf'.
EQPacket: SEQClosing detected, awaiting next zone session, pcap filter: EQ Clie
nt 192.168.1.105
EQPacket: SEQStart detected, pcap filter: EQ Client 192.168.1.105, Client port 1
699, Key port 13325
EQPacket::dispatchZoneData():CharProfileCode:Not Decoded
Loaded map: '/usr/local/share/showeq/Lavastorm.map'
No Zone Specific filter file '/usr/local/share/showeq/filters_lavastorm.conf'.
Loading default '/usr/local/share/showeq/filters.conf'.
TIME: 13:50 04/16/3173
EQ EPOCH OCCURRED AT 794313359 SECONDS POST UNIX EPOCH
CPlayerItems: count=45 size=21066 packetsize=468 expsize=468
No Zone Specific filter file '/usr/local/share/showeq/filters_lavastorm.conf'.
Loading default '/usr/local/share/showeq/filters.conf'.
Your player's id is 2797




I'm asuming that the key at the beginning is either supposed to change when I zone or is showing that the key is not getting to my eq box. I must admit I'm not certain how to verify that it is getting to the llinux box. I have keyring dending it to the ip which is static.

any help would be most appreciated, any flames will be shrugged off as I said at the beginning I was stupider than ya'll.


any ideas?

[baelang]

run your keysniffer in debug mode and post what that says.

you probably don't have the correct offset. (SessionKeyLocation)

[NovaUSC]

I assume you mean keyring -v for debug
hope this is what you wanted

Maximum verbosity
keyring based on keyring version 2.2.
config file name is: C:/keyring/keyring.ini
UncleBen's function is now running.
attempting to enable debug privledges.
Readconfig is reading: C:/keyring/keyring.ini
using ini file Programname: eqgame
ProgramName is: eqgame
key location is: 0x0078bcb8
Send interval is: 60 seconds
destination IP is: 192.168.1.70:13325
scanning for eqgame

after running everquest
it reads

found eqgame - pid = 924

SendSessionKey function called with key: 420170011to destination IP: 192.168.1.70:13325
Sent the key to 192.168.1.70:13325

[Iam_Walrus]

key location is: 0x0078bcb8 -> you haven't updated the config file to use the new offset 0x007c3448. i think the reason the main page has an old offset is because of the expected rapid changes to eqgame.exe with LoY release. i think i am now required to post something about search, so for posterity:


http://seq.sourceforge.net/images/top_search.gif


that being said, it's understandable that you've got the wrong one in there with the conflicting info available.

[NovaUSC]

thank you very very much, that was it!

[fm83]

[Manaweaver]

For god's sake... SEQ is broken.

[NovaUSC]

manaweaver,...dude,...look at the post date, this was before it was broken

[Manaweaver]

Well... it got bumped to the top of the list... stupid post edits.